Troubleshooting KitchenAid Dishwasher Not Cleaning Dishes
When your KitchenAid dishwasher stops cleaning your dishes, it can be a daunting task to figure out why. Here are a few simple DIY steps to troubleshoot and get your dishwasher back to its former glory.
Check Dishwasher Filter
One of the most common causes of poor dishwasher performance is a clogged filter. Over time, food particles, silverware and other debris get trapped in the filter and can cause your dishwasher to work inefficiently. Clean your filter regularly, and replace it at least every three to four months.
To quickly access the filter, open the dishwasher door and insert a flathead screwdriver into the bottom lip of the dishwasher and pry off the filter assembly. Slide out the filter, remove debris and rinse thoroughly. Insert the filter back into the dishwasher and screw back on the assembly.
Check Spray Arms
The spray arms are responsible for spraying water at the dishes, and if they become clogged, your dishes won't get clean. To check the condition of the spray arms, open the dishwasher door and pull out the lower spray arm. Use a pin or needle to clean out any clogged orifices on the spray arm. While you're at it, you can remove the upper spray arm and inspect for obstruction.
Check Float Switch
Most dishwashers are equipped with a float switch, and if it's stuck in the "up" position, it may be stopping the dishwasher from filling up with water. To access the float switch, locate the electric control panel. Unplug the dishwasher, let it sit for 10 minutes and then unencapsulate the electric control panel by unscrewing the panel screws.
Lift the float switch out of the panel and inspect it. Make sure the floating switch isn't stuck and can move up and down freely. If the float switch works properly, the dishwasher should fill up with water. If not, replace the switch with a new one.
Check for Leaks
If the dishwasher isn't performing well, you should check for leaks. Start by shutting off the water supply to the dishwasher, unscrew the feed line from the bottom of the unit and check for any leaks. If there's water on the feed line, you might need to replace it. If the feed line isn't leaking, then the problem could be with the fill solenoid or the drain hose.
Conclusion
Troubleshooting KitchenAid dishwashers that are not cleaning dishes can be a tedious but not impossible task. Most of the time, it's either a clogged filter, clogged spray arms, a stuck float switch, or a leaking feed line. If these DIY steps don't fix your dishwasher, call a local and reliable Appliance Repair at (866) 516-1222 for a thorough and professional repair. If you wish to read more information about KitchenAid dishwasher not cleaning, please click here.
KitchenAid Dishwasher Not Cleaning: Tips and Best Practices
For issues regarding KitchenAid dishwasher not cleaning, we recommend taking the following preventative action steps:
-
Check Water Pressure: Ensure that the water pressure coming into the unit is strong enough for optimal cleaning performance.
-
Check Load Size: Be aware of the size of the load you are trying to clean, as too large of a load can impede cleaning results.
-
Check Cycles: Make sure you are using the correct cycle and cycle settings for optimal results.
-
Clean Filter: Clean or replace the dishwasher filter regularly to reduce food buildup and improve water flow.
-
Clean Gunk: Take care to clean any built up gunk or residue around the door seal and other parts of the interior of the unit to ensure that grime isn’t impairing cleaning performance.
-
Contact a Professional: Should you encounter persistent KitchenAid dishwasher not cleaning issues, contact a professional appliance repair technician. Local reliable repair technicians, such as Local Reliable Appliance Repair, are familiar with the KitchenAid line and are best prepared to correctly diagnose and repair the issue.
Advice On Average Repair Cost for KitchenAid Dishwasher Not Cleaning
Are you experiencing issues with your KitchenAid dishwasher not cleaning properly? There are a variety of repair and installation costs in San Diego to get the job done. The minimum repair or installation cost can range from $100-$300, while complex repair or installation costs can range from $300-$800.
Typically, there is an itemized list of parts that must be replaced in order to properly repair a KitchenAid dishwasher. The most commonly replaced parts are door latch, control panel, water inlet valve, seal, drain hose, and pump assembly.
For a standard door latch repair, it typically costs around $100-$150. Water inlet valve repair is generally around $150-$300, and replacing a control panel or seal can range from $250-$500. Other parts such as drain hoses and pump assemblies may run at a higher cost of $300-$800.
The cost of labor necessary to make the repair often depends on the repairman, but a reliable appliance repairman in San Diego will generally charge approximately $50-$75 per hour. Lastly, the cost of materials necessary to make the repair is also determined by the repairman, which could be additional.
For your convenience, it is highly recommended to call Local Reliable Appliance Repair at (866) 516-1222 for any repairs or installations needed in San Diego.
Troubleshooting KitchenAid Dishwasher Not Cleaning
Having trouble getting your KitchenAid dishwasher to clean? There's no need to stress; help is near. Local San Diego appliance repair shop, Reliable HVAC and Appliance Repair, specializes in same-day service on dishwashers, as well as all of your other appliance and HVAC repair needs.
Reliable offers a lot of customer benefits. As a first-time customer, you're eligible for a $25 discount on labor services. Customers also benefit from their highly trained technicians; each tech has a minimum of 5 years of field experience, confident to diagnose and fix any appliance issue with ease.
At Reliable, you'll find fair and affordable prices for appliance repair services. This local family-owned business is licensed and insured, and their same-day turnaround time gives you a sense of security knowing that your appliance will be back up and running with little disruption to your day.
Reliable is the shop to call when your KitchenAid dishwasher has stopped cleaning. For a reliable, same-day HVAC and appliance repair that you can trust, contact Reliable HVAC and Appliance Repair at (866)516-1222. Save money on your repairs by calling them at your earliest convenience and mention the $25 first-time customer discount.
If you’d like fast and reliable help with your kitchen appliances, look no further than Reliable HVAC and Appliance Repair. Their experienced staff offers same-day service at affordable prices, complete with a $25 discount for first-time customers. Their licenses and insurance provide assurance of quality. Contact Reliable HVAC and Appliance Repair today for assistance with your KitchenAid dishwasher not cleaning. Dial **(866)516-1222.
FAQ: Troubleshooting KitchenAid Dishwasher Not Cleaning Dishes and KitchenAid Dishwasher Not Cleaning
Q1: What should I do if the Dishwasher Does Not Start?
Ensure the latch is completely closed and the door is completely engaged. Check the electrical cord's connection at the wall socket, to the wall or to the rear of the dishwasher, depending upon the model. Make sure the circuit breaker and fuse connected to the dishwasher are functioning. Reset the circuit breaker if necessary.
Q2: How Can I Handlecycle Interruptions?
If the cycle is interrupted during its operation, make sure that the door is securely closed and the latch is engaged. If the cycle was stopped, press the Start/Reset pad to restart the cycle from the beginning. If the cycle was paused, press the Play/Pause pad twice to restart the cycle.
Q3: What if the Water Temperature is Too Low?
Remove any blockages in the water inlet valve. Check the water temperature entering the dishwasher by securely attaching a thermometer to the kitchen faucet. Make sure the hot water is at least 120°F. If there is an issue with the kitchen’s water pressure, reduce the length of the water hoses.
Q4: What Can I Do About Hard Water Buildup?
Ensure the filter is properly cleaned. Check the supply line valve is turned on and the water pressure is between 20 and 120 psi. Have a water softener installed to eliminate minerals that are not dissolved in water.
Q5: What if the Dishes are Not Clean?
Unload the dishes and check the filter for proper cleaning; portions of food particles can accumulate in the filter if not cleaned over time. Have the wash arms and pump assembly checked for blockage. If a built-up layer of food remains, pre-soak the dishes before loading them into the dishwasher. Pre-rinsing or wiping dishes off before they are placed in the dishwasher prevents this food film from forming.
For all your appliance repair needs, contact Local Reliable Appliance Repair at (866) 516-1222.