Heat Pump Won't Turn On? Here's What to Do
If you're like many homeowners, you might feel quite unnerved when you realize your heat pump isn't working. After all, these essential household appliances are instrumental for keeping us warm in the winter, and keep our homes well-regulated in terms of temperature. Not to mention, a faulty heat pump can cost you a bundle in unexpected repairs. Understanding what to do when your heat pump won't turn on can help you save a lot of time and money.
Here Are 5 Common Reasons a Heat Pump May Not Be Working
When your heat pump won't turn on, it often means something is wrong with one of the many components. Here are some of the most common reasons a heat pump may not be working:
- The thermostat has not been calibrated properly.
The thermostat can be a tricky component, and it's important to ensure that it's calibrated properly. If the thermostat is set too low or too high, your heat pump won't turn on. If the thermostat is too low, for example, the heat pump won't kick on until the ambient air temperature reaches the desired temperature. Or if the thermostat is too high, then the heat pump won't kick on until the ambient air temperature surpasses the desired temperature.
- The heat pump is not properly connected or wired.
If the heat pump's wiring or connection isn't connected properly, the heat pump won't work correctly. You should check for any loose wires in the electrical box and make sure the heat pump is properly connected to the power source.
- The fan motor is not working.
If the fan motor isn't functioning properly, the heat pump won't start. This is often caused by worn out capacitors or brushes, or an overheating motor. To find out if this is the case, you should check if the fan blade is spinning when the power is on.
- The heat pump's relay switch is malfunctioning.
If the relay switch is malfunctioning, then the heat pump won't be receiving the proper voltage it needs to run. The relay switch's job is to control the power supply and to transfer the current from one component to another. To find out if this is the case, you can check to see if there is a humming noise coming from inside the heat pump.
- The air filter needs to be replaced.
The air filter traps dirt, dust, and other debris that could clog up the inside of your heat pump and prevent it from working properly. If you haven't replaced your air filter in a while, it might be time to do so. Replacing the air filter is an easy task, and one that should be done on a regular basis.
What To Do If Your Heat Pump is Not Working
Your first step should be to check the thermostat to make sure it's set properly. If the thermostat is not set properly, reset it to the desired temperature. If that doesn't revolve the issue, then move onto checking the wiring, connection, and fan motor. Tightening any loose wires will help to make sure the heat pump is receiving the proper voltage it needs to turn on.
If the fan motor isn't spinning, it could be an indication of worn out capacitors or brushes or an overheating motor. If that's the case, it's important to have a technician come and inspect the heat pump to help detect and diagnose any potential problems.
You should also check the relay switch, as it could be preventing the heat pump from receiving the proper voltage. If the relay switch is not functioning properly, a technician will need to be called to help address the issue.
Lastly, if your air filter is old and needs to be replaced, you can find the right one for your heat pump online or at a local hardware store. Knowing how to install the air filter is a must if you aren't comfortable with this process, you should contact a technician who can help.
Who Should You Call When Your Heat Pump Won't Turn On?
In the event you're unable to resolve your heat pump issue, it's always best to call a local and reliable appliance repair professional to help. If you're located in San Diego, consider taking advantage of the outstanding services offered by Local Reliable Appliance Repair. Their experienced team is available 24/7, and can help to quickly identify and fix the problem. Furthermore, they offer a 100% customer satisfaction guarantee, giving you that peace of mind that your heat pump is not only back in working condition, but that it is also working properly.
If you wish to read more information about Heat pump won't turn on, click here.
Heat pump won't turn on
PLEASE be sure to perform these preventive maintenance actions to avoid Heat pump won't turn on issues in San Diego:
-
Check the thermostat settings. It can be helpful to verify the thermostat is set to the correct fan speed and temperature settings. Adjust the thermostat settings if necessary and make sure that the power switch is on.
-
Be sure to replace the batteries. You should replace the batteries in the thermostat every 6-12 months; doing so should ease any potential problems related to the heat pump not turning on.
-
Check the Circuit Breakers. You should also make sure that the circuit breaker that controls the heat pump is on. Additionally, you may need to flip the circuit breaker off and on again to reset it.
-
Make sure the filters are clean. Dirty filters can cause the system to perform poorly, resulting in the heat pump not turning on. Always make sure to clean or replace the filters as necessary.
-
Conduct regular inspections. It can be helpful to have your local appliance or HVAC technician inspect your heat pump once or twice a year to ensure it is running smoothly. Doing so is the best way to prevent future issues like the heat pump not turning on.
By following these preventive maintenance steps, you will be better equipped to avoid potential heat pump won’t turn on issues in San Diego. It is also important to note that if you are experiencing any further issues, your best option is to consult a professional appliance or HVAC technician.
Average Repair Cost for "Heat Pump Won't Turn On" Issue
When dealing with a heat pump that won't turn on, it's important to get the best possible advice to ensure you get the right repair or installation cost. In San Diego, the average repair cost can range from the minimum repair or installation cost to the more complex repair or installation price.
For the most commonly replaced parts, here is a detailed itemized list:
-
Compressor- The compressor is the heart of a heat pump, and its failure could mean the pump will not turn on. Replacing the compressor will typically cost $750-$2000 in labor and up to $1000 in parts.
-
Thermostat- The thermostat measures the room temperature and controls the furnace. If the thermostat is not functioning properly, it could lead to the heat pump not turning on. Replacing the thermostat will typically cost around $150 in labor and up to $200 in parts.
-
Capacitor- The capacitor is responsible for storing and releasing electricity, which powers the furnace. If the capacitor is not working, it could also cause the heat pump not turning on. Replacing the capacitor could cost around $150 in labor and up to $85 in parts.
-
Relay- The relay is responsible for sending an electrical signal to the furnace. Without this signal, the furnace will not turn on. The cost of replacing the relay could range from $45-$90 in labor and up to $50 in parts.
-
Filter- The filter helps to keep dust and other particles out of the heat pump. If the filter is clogged, it could lead to the furnace not turning on. The cost of replacing the filter could be around $45-$90 in labor and up to $10 in parts.
These are just a few of the most common parts that might need to be replaced in order to repair a heat pump that won't turn on. Depending on the complexity of the repair, more parts may also be necessary. It is therefore recommended to call a local and reliable appliance repair service such as Local Reliable Appliance Repair (866) 516-1222 for accurate assessments on the total repair and installation cost, as well as materials and labor in the city of San Diego.
Heat Pump Won't Turn On? Contact Reliable Appliance Repair
When a heat pump won't turn on, you need a reliable local repair service. In San Diego, that company is Reliable HVAC and Appliance Repair, a local, family-owned business. They offer same-day service and repairs for HVAC and appliance units at a fair and affordable price.
Reliable is the the ideal choice for heat pump repair. Their technicians are highly trained and experienced, with a minimum of 5 years each in the field. Plus, Reliable is a licensed and insured business, so you can feel confident when you hire them to take care of your repair and installation needs.
Need to have your heat pump up and running today? As a first-time customer, you can save $25 on labor costs when you call Reliable Appliance Repair at tel:(866) 516-1222. Get your repair done quickly and easily, and save money, with Reliable Appliance Repair.
FAQ: What Actions to Take If Heat Pump Won't Turn On?
Q: What does it mean when my heat pump won't turn on?
A: When your heat pump won't turn on, it can indicate a potential issue. It is likely due to a power-related issue, a malfunctioning compressor, or a problem with the thermostat.
Q: What should I do if my heat pump won't turn on?
A: First, check to make sure the unit is plugged in and that the circuit breakers and fuses have not blown. Next, check the thermostat and ensure it is set correctly and has power running to it. Finally, if necessary, call a professional for further assistance.
Q: How can I tell if my heat pump's compressor is malfunctioning?
A: One way to tell if the compressor is malfunctioning is to listen for a hum or buzz coming from the unit. When you turn it on, this sound should come from the outdoor cabinet. If no sound is audible, then the compressor may need to be replaced.
Q: What can I do if my heat pump won't turn on and I can't identify what the problem is?
A: If you are having trouble determining what is causing the problem, consider calling a qualified professional for advice and service. Local Reliable Appliance Repair can assist with diagnosing and fixing your unit. Contact them at (866) 516-1222.